- Suntana passport 16 tanning bed maintenance serial number#
- Suntana passport 16 tanning bed maintenance manual#
- Suntana passport 16 tanning bed maintenance archive#
Entries and content can be added/removed/changed manually, as long as, etc. This page is automatically updated by AAlertBot. You need to be near your tanning bed for this page to be helpful. As the largest seller of tanning lamps, we hear this every day, but fortunately, it is pretty easy to figure out what you need using this guide.
Suntana passport 16 tanning bed maintenance archive#
If the tanning bed is new, this usually means a lamp has vibrated loose in the shipping process.< Wikipedia:WikiProject Albums | Article alerts This is an archive of previous Article Alert reports. The page looks long, but it will skip you to the right sections that apply to you. Some installations seem to turn lamp ends dark after a few weeks, others do not, but the UV output of the lamps should be fine. This is normal and will not affect the tanning of the lamp appreciably if the lamps are not older than 2/3rds of their rated life. (This can be tested with a volt meter) This is a dangerous situation and should be corrected by a licensed electrician. Often, a tanning bed needing 20AMP service, but run on 14ga wire will show 120VAC with no load, but drop to 95VAC when the tanning bed is on. If your incoming voltage is correct, the likely problem is insufficient wiring, ie: the gauge of the wire to the circuit is too small. If you have a 120VAC tanning bed, the voltage should be at least 110VAC (preferably 115-125VAC). If you have 208 to 211VAC power (usually ONLY in a business building) then you will need a buck/boost transformer to boost the voltage to a proper level. If you have a 230VAC tanning bed, make sure that the available voltage is at least 215VAC (preferabley 220 to 230VAC) with no load. If your tanning bed has a digital timer, make sure you have selected the proper minute session and pressed the START button. Make sure the knob is not pressed so hard into the tanning bed that it is jammed against the body of it.
If your tanning bed has an analog timer (twist knob style) make sure you turn it passed 5 minutes, then roll it back to the proper time if under 5 minutes. If you are familiar with a volt meter and have one handy, make sure there is power getting to the socket. If it doesn't work, then the problem isn't the tanning bed. If the tanning bed is 120V powered, try moving a lamp or similar plug in device to the outlet and plug it in to test it. Make sure the bed is fully assembled and in the closed position and try again.
Suntana passport 16 tanning bed maintenance manual#
Some tanning beds will not operate unless all the panels are in place and the bed is in the CLOSED position, so read your owners manual and see if you have these safety devices. Make sure all the connections from the bench to the canopy (and to the air cooling bar if so equipped) are connected tightly. If the tanning bed also has a power switch, make sure it is in the ON position, and try both positions just to be sure. Make sure you are turning the timer enough to start the system. Make sure the breaker is in the ON position. New tanning beds: Make sure it is plugged in.īelieve it or not, that is the cause in most cases. These answers deal with home tanning beds in general, but more specifically to the models above. This guide covers many of the most common issues with just about any tanning bed and should help the home tanning bed owner deal with most problems without having to call for service.
Troubleshooting Guide Troubleshooting Guide For SunMaster, Alpha Sun and Virtual Sun Tanning Beds Your new tanning bed is backed by the most comprensive warranty in the industry but even the best tanning bed needs maintenance or a spare part once in a blue moon.
We carry the 60, 75, 90 and other poundage shocks for older Suntana beds, generally under $50 each.ġ-80 SITEMAP Red Light Therapy - Tanning Lamps - Accessories - Parts. This will insure you get the right shock the first time.
Suntana passport 16 tanning bed maintenance serial number#
Because there are so many different shocks, we ask you look at the back of your tanning bed, get the model name, serial number and year built, then call. We do NOT carry shocks for SunQuest or SunVision. Shocks / Pistons Please note that we only carry pistons for SunMaster, Virtual Sun, Suntana, Alpha Sun and PTS tanning beds, and a few for Montego Bay and SonnenBraune.
0 kommentar(er)
